GAIL Previous/Last Year Question Papers for Trainee, Engineers

GAIL Previous Papers:

Job seekers, you can download the GAIL (India) Limited Previous Year Examination Question Papers through this web page if you are going to
appear in Trainee, Engineers etc exam & are preparing for GAIL (India) Limited exam. GAIL (India) Limited Previous year question papers are very significant content for preparation of GAIL (India) Limited Trainee, Engineers & other Exam.

Every year lots of applicants wrote in exam to be a part of this organization. It helps in therefore many ways to obtain success in GAIL (India) Limited exam. So, if you are preparing for GAIL (India) Limited exam they need to prepare through previous year papers of GAIL (India) Limited in order to get well knowledge of questions and for that you will have download it from official website of organization.

Candidates are suggested to download GAIL Previous Year Papers of this examination and receive an idea of the pattern of exam, types of question, time management & other in order to score good in this exam. Various applicants have applied for GAIL (India) Limited Examination Notification successfully. Job seekers need to do better preparation to join GAIL (India) Limited on applied position.

GAIL Exam Pattern & Syllabus Topics:

Subject
Questions
Duration
General Knowledge
15
2 Hours
Quantitative Aptitude
35
Based on S/W & IT
100
  • The written paper consists of 150 questions.
  • The exam has the duration of 2 hours.
  • The questions will be of subjective types.
  • The topics for written exam are
  • JAVA Programming
  • C and C++ etc.

These are the written exam subjects:

  • General Knowledge.
  • Qualitative Ability.
  • English verbal.
  • Logical reasoning

GAIL Previous Year Question Paper Trainee, Engineers etc:

1. The resultant of parrallogram?
Ans: R=(P^2+Q^2+2PQCOSQ)^.5
2) Centre of gravity of hemi sphere?
Ans: 3r/8
3) Time of flight of a projectile?
4) Modulus of elasticity for a tapering section?
5) For what angle does maximum shear stress on a body exist when body is subjected to stress in one plain?
6) If a cantilever beam is loaded wid point load at its free end when the load increases
at which section it will break first?
7) mx.torsion on a  shaft is in what praportion to the dia of shaft?
8) 3-4 ques on spring stifness(numerical)?
9) What kind of rivet arrangement is called as diamond riveting?
10) Which among dese is not dimensionless?
a) Absolute viscosity b) Specific volume c) Specific gravity
11) Laminar flow characteristic related question?
12) Specific speed of turbine?
13) Unit power of turbine?
14) Discharge through a reciprocating pump for single and double acting
15) Which one is intensive property?
a) Entropy b) Enthalpy c) Density
16) Which among these has highest efficiency?
a) otto b) Diesel c)dual
17) Some efficiency related question on rankine cycle and brayton cycle
18) 3 questions from steam nozzle and turbine like nozzle efficency
19) Velocity related questions from impulse turbine
20) One numerical from gas turbine
21) Genral day to day life question based on heat transfer so understand the concept
22) One numerical based on cross and parallel flow
23) One numerical on LMTD
24) What is equivalent length of simple pendulam which gives the same frequency as
compare to compound pendulam.
25) One numerical on no teeth and speed of gear
26) Pitch circle is what kind of circle in a gear one gear wid 200 teeths anodr wid 50 teeths meshed 2 gadren how many raotation of smaller gera will make 1 revolution of
bigger gear
Ans: 4
27) 2 concept question on governers
28) 2 questions based on balancing of rotating masses
29) 2 questions related to vibration
30) 1 questions on limit fits and tolerance
31) What is endurance limit ratio
32) What is fatigue or stress concentration factor
33) What is the strength of riveted joint
34) What kind of thread is used if power is to be transmitted in 1 direction only
35) Overhauling case will have frictionb angle greater, equal or less than helix angle
36) what combination of material is used 4 bearing manufacture
37) Magnesium is added for which purpose
38) For achieving hardness which procees should be carried(Annealing, normalising,
martempering etc)
39) 1 questions related to submerged welding
40) Which welding is done for joining shank of a drill bit (Flash butt welding)
41) What to be use for measuring angle and for locating the w/p at some angle
42) How many nomenclatures are there to completely define a single poin cutting tool
43) One concept question related to upmilling(climb milling)
44) To find out pessimistic time of any project (pert)
45) 2 very basic ques on (fire management)
46) 3 questions related to (Industrial production) like related to routing, schrduling etc
47) 3 economics question (depreciation value calculation, money related conceptual
questions)
48) 2 question on (Product design)
Aptitude was genral and easy.

How to Prepare For Exam or Read by Video -


If you want to check GAIL Previous Papers directly then you must follow given below link:-


0 comments:

Post a Comment

Powered by Blogger.